配置

配置 Cudy TR3000 openwrt

连接

插入网线接到cudy tr3000的lan口，设置 dhcp，正常能获取 10.0.0.x 的 ip 地址。

浏览器打开

http://10.0.0.1

用默认的帐号 root/root 登录。

打开 系统 -> 管理权，修改密码。

wan 口先接入其他路由器，方便配置时进行各种下载。

打开 网络 -> 接口 , 默认 wan 使用 dhcp 正常已经连接网络了。

删除 wan6, 编辑 lan，将 lan 的 ip 地址修改为 192.168.5.1 。

保存后打开 192.168.5.1 重新登录。

更新

打开 istore -> 维护， 更新 istore。

usb 网络

opkg update
opkg install kmod-usb-net-rndis usbutils

安装过程：

opkg install kmod-usb-net-rndis usbutils
Downloading https://dl.openwrt.ai/releases/24.10/targets/mediatek/filogic/6.6.116/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_core
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/base/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_base
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_packages
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/luci/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_luci
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/routing/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_routing
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/kiddin9/Packages.gz
Updated list of available packages in /var/opkg-lists/kwrt_kiddin9
Installing kmod-usb-net-rndis (6.6.116-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/targets/mediatek/filogic/6.6.116/kmod-usb-net-rndis_6.6.116-r1_aarch64_cortex-a53.ipk
Installing kmod-mii (6.6.116-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/targets/mediatek/filogic/6.6.116/kmod-mii_6.6.116-r1_aarch64_cortex-a53.ipk
Installing kmod-usb-net (6.6.116-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/targets/mediatek/filogic/6.6.116/kmod-usb-net_6.6.116-r1_aarch64_cortex-a53.ipk
Installing kmod-usb-net-cdc-ether (6.6.116-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/targets/mediatek/filogic/6.6.116/kmod-usb-net-cdc-ether_6.6.116-r1_aarch64_cortex-a53.ipk
Installing usbutils (017-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/usbutils_017-r1_aarch64_cortex-a53.ipk
Installing libusb-1.0-0 (1.0.27-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/base/libusb-1.0-0_1.0.27-r1_aarch64_cortex-a53.ipk
Installing libevdev (1.13.1-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libevdev_1.13.1-r1_aarch64_cortex-a53.ipk
Installing libudev-zero (1.0.3-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libudev-zero_1.0.3-r1_aarch64_cortex-a53.ipk
Installing usbids (0.387-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/usbids_0.387-r1_aarch64_cortex-a53.ipk
Configuring libevdev.
Configuring libusb-1.0-0.
Configuring kmod-mii.
Configuring libudev-zero.
Configuring usbids.
Configuring usbutils.
Configuring kmod-usb-net.
Configuring kmod-usb-net-cdc-ether.
Configuring kmod-usb-net-rndis.

拔掉网线，usb连接手机，选择usb网络共享。

openwrt 页面进入 网络 -> 网口配置

eth0 显示“已断开”，这个是网线。

多了一个 usb0, 当前还是显示为 “已断开”，在 wan 这一行勾选 usb0， eth0 的勾选会自动取消。

点击 “保存并应用” 。再刷新页面，usb0 显示为绿色已经连接。

zerotier

安装 zerotier

在页面登录之后，进入 istore 页面，进入 istore ，选择更新 istore。

搜索 zerotier，找到 zerotier 之后点击安装：

istore (完成于： 11/22/2025, 4:50:20 PM) > is-opkg install 'app-meta-zerotier'

Try mirror server https://repo.istoreos.com/repo
Installing app-meta-zerotier (1.3.0-1) to root...
Downloading https://repo.istoreos.com/repo/all/meta/app-meta-zerotier_1.3.0-1_all.ipk
Installing libminiupnpc (2.2.8-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libminiupnpc_2.2.8-r1_aarch64_cortex-a53.ipk
Installing libnatpmp1 (20230423-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libnatpmp1_20230423-r1_aarch64_cortex-a53.ipk
Installing zerotier (1.14.1-r3) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/zerotier_1.14.1-r3_aarch64_cortex-a53.ipk
Installing luci-app-zerotier (26.218.43438~65032d3) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/kiddin9/luci-app-zerotier_26.218.43438~65032d3_all.ipk
Installing luci-i18n-zerotier-zh-cn (git-25.156.35898-bfd1fcd) to root...
Downloading https://repo.istoreos.com/repo/all/nas_luci/luci-i18n-zerotier-zh-cn_git-25.156.35898-bfd1fcd_all.ipk
Configuring libminiupnpc.
Configuring libnatpmp1.
Configuring zerotier.
disabled in /etc/config/zerotier
Configuring luci-app-zerotier.
Configuring luci-i18n-zerotier-zh-cn.
Configuring app-meta-zerotier.
Try mirror server https://repo.istoreos.com/repo
Package zerotier (1.14.1-r3) installed in root is up to date.
Package luci-app-zerotier (26.218.43438~65032d3) installed in root is up to date.
Package luci-i18n-zerotier-zh-cn (git-25.156.35898-bfd1fcd) installed in root is up to date.

注意不要直接安装 zerotier 或者 luci-app-zerotier

# 这个会安装 zerotier，但是没有界面
opkg install  zerotier
# 这个会安装 luci 界面，但有些 openwrt 比如我的 cudy tr3000 用的 kwrt 也会没有页面现实。
opkg install luci-app-zerotier

也不要在 系统 -》软件包内安装 openwrt 或者 luci-app-zerotier，问题都一样，没有页面。

设置 zerotier 插件

openwrt 下打开 vpn -> zerotier,

Global configuration：

  • 启用: 勾选
  • Allow input traffic: 勾选

Network configuration, 配一行就可以了：

  • NetworkId
  • Allow managed IP/route: 勾选
  • Allow global IP/route: 勾选
  • Allow default route: 勾选
  • Allow input: 勾选
  • Allow forward: 勾选
  • Forward interfaces： 不选，默认就是all （Leave empty for all.）

配置 zerotier 服务

登录 https://my.zerotier.com/ ，打开自己的 network， 刷新 Members 成员列表，能看到有一个新的成员出现，默认是没有通过认证的。

  • 勾选 Authorized
  • name：cudy
  • description： cudy-ax3000路由器
  • ip地址设置为 192.168.192.50

再刷新列表，就能看到这个新的成员分配到新的地址，而且显示 auth 通过。

打开 网络 -> 防火墙 -> 常规设置：

  • 入站数据： 接受
  • 出站数据： 接受
  • 转发： 接受

ssh 登录到 openwrt，默认密码 root/root。

$ ip addr

10: ztw4lflcku: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2800 qdisc fq_codel state UNKNOWN group default qlen 1000
    link/ether 96:4e:39:22:37:d1 brd ff:ff:ff:ff:ff:ff
    inet 192.168.192.50/24 brd 192.168.192.255 scope global ztw4lflcku
       valid_lft forever preferred_lft forever

验证一下。

分别在 cudy 和一台连接 cudy 的机器上执行：

ping 192.168.192.20
ping 192.168.192.30
ping 192.168.192.40
ping 192.168.192.50

ping 192.168.2.1
ping 192.168.3.1
ping 192.168.4.1
ping 192.168.5.1

正常此时应该可以 ping 通的.

openclash

安装

进入 系统 -> 软件包，先更新列表，再在过滤器中输入 openclash，显示 luci-app-openclash，点击安装。

opkg --force-overwrite install luci-app-openclash

Installing luci-app-openclash (0.47.028-r30) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/kiddin9/luci-app-openclash_0.47.028-r30_all.ipk
Installing libruby3.3 (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libruby3.3_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-digest (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-digest_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-enc (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-enc_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-pstore (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-pstore_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-bigdecimal (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-bigdecimal_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-date (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-date_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-stringio (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-stringio_3.3.9-r1_aarch64_cortex-a53.ipk
Installing libyaml (0.2.5-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/libyaml_0.2.5-r1_aarch64_cortex-a53.ipk
Installing ruby-psych (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-psych_3.3.9-r1_aarch64_cortex-a53.ipk
Installing ruby-yaml (3.3.9-r1) to root...
Downloading https://dl.openwrt.ai/releases/24.10/packages/aarch64_cortex-a53/packages/ruby-yaml_3.3.9-r1_aarch64_cortex-a53.ipk
Configuring libruby3.3.
Configuring ruby.
Configuring ruby-digest.
Configuring ruby-enc.
Configuring ruby-pstore.
Configuring ruby-stringio.
Configuring ruby-bigdecimal.
Configuring ruby-date.
Configuring libyaml.
Configuring ruby-psych.
Configuring ruby-yaml.
Configuring luci-app-openclash.

配置

打开 服务 -> openclash， 提示没有下载内核，选择下载。

但下载非常慢，很容易失败，从运行日志中可以看到：

2025-11-22 17:15:39 【/tmp/clash_meta.tar.gz】下载失败：【curl: (28) Operation timed out after 60000 milliseconds with 768899 out of 7198810 bytes received】
2025-11-22 17:15:21 【/tmp/openclash_last_version】下载失败：【curl: (28) Operation too slow. Less than 1 bytes/sec transferred the last 30 seconds】
2025-11-22 17:13:33 下载进度：【clash_meta.tar.gz - 12%】
2025-11-22 17:13:28 下载进度：【clash_meta.tar.gz - 11%】
2025-11-22 17:13:23 下载进度：【clash_meta.tar.gz - 10%】
2025-11-22 17:13:17 【/tmp/openclash_last_version】下载失败：【curl: (28) Operation too slow. Less than 1 bytes/sec transferred the last 30 seconds】

打开 openclash 的 插件设置 -> 版本更新，找到 meta 内核的"下载最新版本内核", 点下载。

找到下载下来的 clash-linux-arm64.tar.gz，解压得到 clash 文件，然后上传到 clash 目录下

scp ./clash root@192.168.5.1:/etc/openclash/core/clash_meta

刷新 openclash 页面，可以看到内核已经更新成功。

在配置订阅，配置管理依次操作，设置好配置文件，然后启动 openclash。可以查看运行日志，看是否遇到问题。

成功启动后，打开 覆盖设置 -> 设置 SOCKS5/HTTP(S) 认证信息, 取消勾选, 不开启代理的认证。

精简

虽然默认的固件已经很精简了，但有些软件包还是占用了一些空间，可以精简一下。

卸载 Passwall：

$ opkg list-installed | grep passwall
luci-app-passwall - 25.11.1-r1

$ opkg remove luci-app-passwall
Removing package luci-app-passwall from root...
Not deleting modified conffile /usr/share/passwall/rules/proxy_host.

$ rm /usr/share/passwall/rules/proxy_host

卸载 WireGuard：

$ opkg list-installed | grep wireguard
kmod-wireguard - 6.6.116-r1
luci-proto-wireguard - 26.313.53093~ae2aec8
wireguard-tools - 1.0.20210914-r4

$ opkg remove kmod-wireguard luci-proto-wireguard wireguard-tools
Removing package kmod-wireguard from root...
Removing package luci-proto-wireguard from root...
Removing package wireguard-tools from root...

刷新页面

插件已经卸载，但 LuCI（OpenWrt 的 Web 界面）缓存里还保留了旧的菜单链接，点击时会报错。

执行以下命令删除缓存文件：

rm -f /tmp/luci-indexcache
rm -f /tmp/luci-modulecache/*

重启路由器。

其他

设置无线，mac地址过滤。

总结

刷新到了最新版本的 openwrt 固件，然后安装了 zerotier，openclash 两个插件，支持 usb 网络连接手机。

基本够用了。